Toradex Easy Installer touchscreen issue on i.MX7D
Hello, I have experienced an issue when using Easy Installer on i.MX7D module, running on Aster carrier board. The display is working as expected, but the vertical axis of the touchscreen is flipped,...
View ArticleTEZI can't install verdin TDX embedded linux reference minimal image (Dunfell)
I am using TEZI 2.0b5 (Mai 2020). This version can't install TDX embedded linux reference minimal image (It says: image requires a newer version of the installer]. Which version do I need?
View ArticleColibri iMX8X V1.0B - TEZI
Hello, I am trying to update TEZI on my module. I've tried prerelease (2.0b6 | 2020-11-02) and few nightly releases (246, 247, 248, 252). In all of these recovery-windows.bat contains 2 uuu.exe...
View ArticleReinstalling Toradex Easy Installer
Greetings, My team and I plan on getting our hands on a Toradex SOM (most likely an Apalis iMX8X) and do Yocto development on it. We went through the [hands-on document][1] for building Yocto images,...
View ArticleTEZI 2.0b6, headless Iris board, no support for VNC for Windows
Hi Version 1.8 works via USB RNDIS, display not connected (actually no display to connect). Version 2.0b6 doesn't work. ![alt text][1] VNC downloaded from [here][2]. It worked well with TEZI 1.8. [1]:...
View ArticleEasyInstaller shows [image requires a newer version of the installer] for...
Colibri module in Toradex Col.Ev. Board is running EasyInstaller v1.7. I follow the quickstart guide for using TorizonCore, so I downloaded the EasyInstaller package for "TorizonCore with evaluation...
View ArticleToradex easyinstaller with imx6ull does not detect images on USB
Hi TDX support, My platform is Colibri iMX6ULL 512MB Wi-Fi / Bluetooth IT V1.1A on iris v1.1 carrier board. I'm using TEZI version: Colibri-iMX6ULL_ToradexEasyInstaller_1.8-20181019 My objective is to...
View ArticleWrite image from TEZI
Hi, I'm not very expert on tezi because an old colleague of mine took care of it. I have a Yocto image and i want to flash it on my Apalis module so I put the extracted image on a USB pendrive. I start...
View ArticleRun Toradex Easy Installer on Colibri iMX8X
Hello, my procedure for flashing a Linux image was the following on an iMX7D on Viola Board: - Download Easy Installer and extract onto micro SD card - Insert Sd card in the Viola Board and run the...
View Articlewrapup.sh reboot problem in TEZI 1.8
Hello everyone, When we want flash image, we want to reboot by using wrapup.sh. But it doesnt work in TEZI 1.8. By using older modules we reach TEZI 1.7 , and we saw that reboot -f works properly. Are...
View ArticleFlash space Capacity = 0MB during recovery mode.
I am using these hardware: -Apalis iMX8QXP 2GB Wi/BT V1.1B -Apalis carrier board Below is the screenshot when I enter "recovery mode" -. Reading Config Block Fail ![alt text][1] -. Enter info manually...
View ArticleUSB not detected on the host for the imx7 evaluation board "Easy installer"...
Hi, I have an evaluation board (Colibri iMX7D wirh Evaluation board V3.2B) which already has an image installed (it doesn't boot into the Easy installer. I have been following the steps described: *...
View ArticleTEZI autoinstall with AVAHI lockup,TEZI Colibri iMX6 AVAHI autoinstall lockup
I am trying to set up a system for unattended flashing over ethernet using the instructions for [unattended flashing over ethernet][1] and [auto installation][2]. The TEZI 2.0b6 image is on a flash...
View ArticleIMX8QP 2GB WP V1.1B Recovery Mode
Hello, Following the instructions for entering recovery mode for the IMX8, I seem unable to do so. I am using an Apalis Eval Board V1.1C with an IMXQP WB 2GB V1.1B. I have the following configuration:...
View ArticleReading Config block failed
I have an iMX8QM I tried to flash a custom Yocto image (.tar) with ToradexEasyInstaller. I enter the recovery mode well by hardware and the easy installer files start to load and writing my image. It...
View ArticleThe TEZI GUI disappears when using SD with 3 partitions.(Close)
I met a bug where the TEZI GUI was not displayed. The TEZI GUI will appear for a moment, but it will end immediately and the Toradex logo will be displayed. However, it seems that writing is being...
View ArticleToradex Easy Installer failed to install Torizon Core image
The Toradex Easy Installer failed to install Torizon Core on the verdin-mini with an downloading/writing image error after reaching 100% of the progress bar: ![alt text][1] This happens one time with...
View Article[TEZI] Progress bar does not take into account size of sdcard tarball - overflow
Hi everyone, When I write a tarball into a SD card during I load a custom image with TEZI, the size of tarball is not take into account in the remaining size of complete image, there is then an...
View ArticleInstalling Easy installer from USB thumb drive
Hi We want to install Easy installer (Tezi) through USB Thumb drive not from OTG. Has anyone performed this? We tried below steps *) Executing "bmode_usb" command from active/running linux image...
View Article